What is an Askona bed with a lifting mechanism?

Advantages and disadvantages of a bed with a lifting mechanism

The main advantage of such beds is space saving. The sections under the bed have enough space to store bulky items. Partially, such a bed can replace a wardrobe. Due to the fact that access to the internal filling is carried out by lifting the top bar, there is no need to free up space next to the bed in order to freely pull out the drawers.

In addition, the flooring or carpet will not suffer from the wheels. Even if you do not use the bed as a storage place, the lifting mechanism will be convenient. Thanks to it, it is much more convenient to clean under furniture.

A bed with a lifting mechanism will be a good solution for a small bedroom.

Do such beds have any disadvantages? Alas, the cost of the structures is an order of magnitude higher than the price of conventional models without a lifting mechanism. The second nuance is less significant. Dust will regularly accumulate under the bed, so things will have to be stored in boxes or containers.

Advantages of lift-up beds

Gas lifts are installed in various types of beds. Some models are complex transformable systems. In others, the piston is used only to lift the frame on which the mattress rests.

Several advantages of such products should be highlighted:

Practicality.

Durability . Gas lifts not only reduce the load on a person, but also protect the bed frame from rapid destruction.

Simplicity. To activate the mechanism, significant effort and special skills are not required. Even a child can do this.

Characteristics of a bed with a lifting mechanism

Typically, such beds are equipped with the most reliable components and durable slats. That is, the design is created taking into account all mechanical loads. The furniture consists of a flat base, a niche and a built-in mechanism, due to which the upper part rises up or to the side.

There are several types of bed lifts.

Most modern models have a gas lift, but there are also beds with spring and manual mechanisms. You can assemble such furniture with your own hands: it is not as difficult as it might seem at first glance.

Design features

A gas lift is a mechanism that is designed to lift the surfaces associated with it. The device has the following structural parts:

a piston with a rod used to direct the force;
oil damper for a smooth ride thanks to the shock-absorbing effect;
cylinder with gas, which is usually nitrogen.

Note! The device cannot be disassembled. The gas composition in the inner part is placed under high pressure. If the design is damaged, the main properties of the mechanism are lost.

Thanks to the use of gas lift, proper support of the spine is provided. This eliminates joints and uneven parts on the surface. And this contributes to comfort and good rest.

Types of lifting mechanisms

In modern models, a gas lift or spring mechanism is more common. The manual hinge system was popular several decades ago; now such furniture is rare.

The mechanism can be made of different materials.

Manual

The simplest mechanism without auxiliary devices that simplify lifting the base. But at the same time, it is the most durable. It works due to the movement of furniture hinges. During lifting, all the weight rests on the hands, so not everyone can access the internal contents.

The French folding bed transformation mechanism has become widespread.

For a child, this task will be difficult to accomplish. If handled carelessly, the housing may become deformed. Especially if the bed is made of inexpensive chipboard that does not withstand frequent use.

Spring

This is a budget option that is installed in economy class beds, as well as in some mid-price models. When lifting, the weight of the body partially falls on the springs, thanks to which even a person who does not have developed physical strength can cope with it.

A double bed with a lifting mechanism on springs costs significantly less than its counterpart on gas shock absorbers.

However, it will be difficult for the child to lift the base. A serious drawback of the mechanism is its short service life. Typically, manufacturers claim 5 years during which the device remains usable. The springs are then stretched.

On gas shock absorbers

Gas lift is the most advanced mechanism. Lifting the bed requires virtually no physical effort: the bulk of the weight falls on the device. It works silently, the base lowers and rises smoothly, and is securely fixed in a vertical position.

Lifting mechanisms can be manual, with springs or with gas shock absorbers.

The mechanism can be installed in any bed. Manufacturers claim a 10-year service life for the device. The only drawback is the high cost compared to other models. But in the long term, the purchase will be profitable.

Everyone chooses their own bed transformation mechanism.

Gas

The bed gas lift is based on a simple mechanism that operates smoothly, silently and reliably. If the load is correctly calculated and a shock-absorbing device is selected, such a product can be used for up to 10 years. The bed cabinet includes additional equipment with a pneumatic gas lift with two stops.

Experts recommend choosing the latter option, which is characterized by ease of use and smooth operation. The cost of such a gas lift for a bed is higher compared to analogues, but the use of the device is fully compensated not only by convenience, but also by safety.

Based on the operating principle, elevators are divided into two groups:

Automatic, not requiring human effort and close control to raise/lower the bed.
Frictional, with less pressure, but providing for stopping the raised part of the bed in any desired position.

Please note that the former are more popular, therefore they lead in sales on the market.

How to choose a bed with a lifting mechanism

To choose suitable furniture, you should focus on the operating conditions:

if you do not need to regularly raise the base (for example, things that are rarely used are stored in the bed), you can purchase a model with a manual mechanism;
For regular use, spring installations or a model with gas shock absorbers are suitable;
For a children's room, it is better to choose a bed with a gas lift, but one with a spring mechanism is also suitable if you plan to change the furniture within a few years.

You can always get great pleasure from creating a bed with your own hands.
It is important to pay attention to the materials of manufacture, namely the strength of the lamellas. Budget models usually use inexpensive chipboard, which can quickly become unusable. The best in comparison with them will be beds made of MDF. This material is durable and safe.

Once the base is raised, you will have access to a lot of space.

The larger the furniture, the more weight will be placed on the mechanism. According to the standard, such beds are 2 m long and 90 cm wide (single) and 2 m (double). The dimensions of the product must be taken into account when choosing a mechanism. It is worth checking with the manufacturer what loads it is designed for.

Disadvantages of Askona beds

Reliable, stylish and modern bed with a high and voluminous backrest Silvana

Among the possible disadvantages of such an acquisition, as a rule, is the unpleasant smell of eco-leather, which persists for a short time after installing the new purchase. However, even critics are forced to admit that within a few days this smell completely disappears.

Simple and simple, elegant and stylish, the Domenico bed warms up your bedroom and sets the tone for the entire interior.

Another complaint about this bed is that there is only one standard bed length option - 2m. Some would prefer a slightly more compact size. But the width of standard models varies depending on your preferences. There are beds with a width of 80, 90, 140, 160, 180 cm, single or double.

The durable, cozy Leo bed will provide your child with a place where he can fully relax and prepare for the new day.

The Elisa bed with removable covers is the ideal solution for a modern interior

How to assemble a bed with a lifting mechanism with your own hands

If you select high-quality materials and accurately calculate the drawings, you will be able to assemble a bed with a lifting mechanism with your own hands. For production, chipboard, OSB, MDF or plywood are used. The body can be made from solid wood, if possibilities permit.

But the lifting bar should be made of lighter materials so as not to put a high load on the mechanism. It is better to opt for MDF: these are safe boards made from chips and resin, they are durable and easy to use. It is also important to choose upholstery fabric and filling.

Required tools and fasteners

Before you begin assembly, you need to prepare the manufacturing materials and the necessary set of tools:

screwdriver;
grinder with a disc for metal;
welding machine;
jigsaw;
construction hair dryer;
furniture stapler;
roulette;
level;
pencil;
steel strips;
ties, corners, brackets.

Before work you need to prepare all the necessary tools.

Stages of work

The first step is to cut out the parts according to the drawings.

Further instructions for assembling a bed with a lifting mechanism are as follows:

body assembly;
installation of legs, corner ties;
installation of a lifting mechanism;
frame fastening.

At the first stages, the work is carried out in the same way as assembling a regular bed. The only difference is the installation of the lifting mechanism.

Assembling the base and box

The perimeter of the body consists of a headboard and 3 drawers, which must be connected to each other with furniture ties or corners and brackets that are fastened with screws. It is better to do the work with a partner who will hold the parts being connected.

Every part of the bed must be thought out.

It is important to check the evenness of the floor: if the bed is installed skewed, the mechanism will not be able to function normally. How to assemble the base and body:

parts are connected on the floor to avoid distortions;
to level the corners, use a construction square;
the screed is carried out using construction corners, the heads of the screws should be slightly buried in the thickness of the slab;
the joints are additionally glued;
cuts are processed to remove burrs;
For double beds, it is recommended to make an additional longitudinal post in the middle.

Different models can use a variety of longitudinal force elements.
After assembling the box, you do not need to immediately tighten the bolts. This is done only after the structure is level. And checking the accuracy of the angles. Transverse partitions are installed in the finished box, which will create sections for storing things.

Serial furniture is usually equipped with an assembled mechanism.

This stage can be skipped if there is no need to create separate “boxes”.

Important! Wooden materials must be pre-treated with stain, sanded and varnished after assembly.

The lifting box is assembled according to the same principle as the base. For production, 3 drawers are used. The base of the bed frame and slats are attached to them.

Installation of legs and installation of corner ties

The legs are attached either to special platforms that are located on the frame elements, or bars (40x50) are screwed into the structure with screws.

Important! Using a level, you need to determine the height of different sections in order to align the legs in height.

The base on which the mattress will subsequently be placed is usually equipped with slats.
The most important stage in assembling the body is connecting the parts with corners. Before fastening, you must check that all angles are exactly 90 degrees. After joining, it is better to treat the joints with glue and remove any excess immediately. Installation of the lifting mechanism

Important! The weight of the lift bar falls not only on the arms and shock absorbers, but also on the fittings. Therefore, it is necessary to choose the most reliable fastenings.

The berth with built-in lifting mechanisms ensures ergonomic space.
You can make the lifting mechanism yourself, but it is better to order a ready-made one from a furniture manufacturer or in specialized stores.

How to install the mechanism:

the upper bar of the mechanism is mounted to the base of the box and the sheathing of the berth; this will require a metal stiffener bar made from rolled angle steel;
To facilitate the sliding of the hinges, a lower support bar is attached to the box.

After installation, you need to check the strength of the fasteners and tighten (but do not overtighten) the bolts.

Attaching the frame and mattress supports

Using self-tapping screws, slats (approximately 20x80 mm) are attached to the inside of the lifting bar. They are aligned along the lower edge of the perimeter.

Long-term and uninterrupted operation is only possible with proper assembly of the furniture.

Slats are placed on the slats, the length of which corresponds to the length of the furniture. They are mounted on support rails in 15 cm increments. You can use plywood if an additional central post is installed.

Common mistakes

How to assemble a double bed according to the instructions is not an easy question; even if you follow all the instructions, you can make a number of mistakes that can lead to loss of time and incorrect assembly of the product. Typical errors include:

Beginners should not start by assembling massive and large parts. You need to start small, and there will be fewer mistakes;
before starting furniture assembly, the number of parts and fasteners is not checked against the instructions; parts of the furniture are not examined for chips, scratches, or damage;
inattentive study of the instructions can negatively affect the assembly process - the parts may be similar to each other, which will lead to their incorrect connection;
Fasteners from the set may be similar to each other, but used in different connections due to their diameter. And if in one case a long fastener can be used instead of a short one, then a short fastener will not be suitable for the role of a long fastener;
by collecting parts on a carpet or any other soft surface, you can ensure that some of the parts get lost;
Most of the bed parts are made of MDF, and if you make holes with a drill, the panels can burst. Bolts and screws are easily screwed in with a screwdriver;
Failure to follow the assembly sequence according to the instructions will result in the double bed with a lifting mechanism being assembled incorrectly;
If you do not glue some parts together with special glue, over time there will not be the required density between them.

Everyone dreams of having a comfortable and beautiful bed, but for small-sized housing it is difficult to choose a model that would simultaneously meet all these requirements. Here it is important to rationally use the limited area of the room, so you should pay attention to the option with a lifting mechanism. Self-assembly of a bed with a lifting mechanism according to the instructions in the video is a completely accessible process.

Having a comfortable bed allows a person to get enough sleep and regain strength before a new day. If the bedroom is not large in size, do not be upset. It is enough to choose a bed with a lifting mechanism, which is characterized by compact dimensions, high comfort and original design. Moreover, the cost of such furniture can vary, so you can choose an option to suit any budget. And to save even more, it’s worth analyzing how professionals assemble such structures and doing the same.

The assembly diagram of a bed with a lifting mechanism is quite simple, but first you should know the main advantages of such furniture. Products of this type provide a person with comfort during rest and sleep, but do not take up much free space in the room. The lifting mechanism is attached to a spacious box, inside of which you can store bed linen and bedspreads. Thus, with a small area, you can solve the problem of storing bedding. For these reasons, beds with a lifting mechanism are so popular among owners of small city apartments.

To independently assemble such a structure, you will need the following tools and materials:

hardware;
set of screwdrivers, ring wrench, screwdriver;
wrench;
yardstick;
building level;
hammer;
a sheet of paper, a simple pencil.

Thus, the work will not require expensive equipment or rare tools, which greatly facilitates the preparatory stage.

Common problems and errors

The main problem when assembling a bed with a lifting mechanism is non-compliance with calculations and inaccurate connection of corners. It is very important to respect the dimensions of the slats. If it is not possible to cut sheet material at home, it is better to order a cut.

Classic double bed sizes with an additional lifting mechanism.

Precise joining of the corners will ensure the reliability of the structure and the precise fit of the lifting bar to the base. If a lifting mechanism with gas lift is selected, it is necessary to clarify its reinforcement: for which bed models it is suitable. It is mounted using nuts with a locking ring and fluoroplastic washers. The fastening cylinder should be facing up.

Bed with wide sides, made of wood.

It happens that the lifting bar is quite difficult to lift. It could be the fasteners that are screwed on too tightly. When installing, they must be tightened all the way and then loosened slightly to obtain minimal play. Then make sure that the mechanism works correctly.

The entire assembly process must be carried out strictly according to the instructions.

To make it easier to lift the slats, you should install handles on the frame, as well as a mattress stopper. This simple method will make using the bed even more convenient. A bed with a lifting mechanism, assembled by hand, is much more reliable than factory models.

To complete the assembly, all that remains is to lay the bottom of the bed and put the cover on its perimeter.

It's all about being able to choose the materials yourself. Such furniture will cost less. Considering that the assembly process is not that complicated, this can be a serious budget saver.

Possible difficulties during work

Without practical experience in assembling furniture or making minor mistakes, you may encounter difficulties. The following installation difficulties are common:

Step-by-step furniture assembly

Having become familiar with the design features of the transforming bed, you can begin the step-by-step assembly of the structure with a lifting mechanism in the following sequence:

First of all, the wall box is installed, in which the sleeping place will be hidden. To properly assemble a niche, experts recommend making a drawing of the future structure according to the dimensions of the transformable bed. This stage can be simplified by visiting an Internet resource on the relevant topic, where various drawings are posted.
At the next stage, you need to correctly lay out both the transverse and side boards in order to fix the corners for support to them.
The components of the box are fixed to each other, not forgetting to control the level of the corners so that the assembled structure fits smoothly into the wall niche.
Thick plywood or a sheet of chipboard is attached to the bottom support rail.
The upper support corners are assembled.
The hinges are fixed at the head of the bed to the transverse support rail.
Lifting spring systems are fixed to the longitudinal part of the frame, 80-85 cm below the headboard.
In place of the same fastening, both closers and gas type shock absorbers are installed. During installation, be sure to check the symmetry of the arrangement of elements. If the fixation is incorrect, the structure will be overloaded on one side, which, in turn, will disable the entire lifting system.
The support legs, equipped with a protective pad, are fixed to the side parallel to the headboard.
The slats on which the mattress will rest are fastened with self-tapping screws along the top of the support corners.

Next, all that remains is to put the mattress in its rightful place and check that the transformable bed is assembled correctly.

As you can understand, the process of installing furniture with a lifting mechanism is not so complicated if home craftsmen follow the instructions and advice during the work. And video instructions on the Internet resource, conducted by real professionals in their field, will help you solve any difficulty.

Errors when assembling a bed

A sleeping place with built-in lifting mechanisms ensures ergonomic space and eliminates the need for furniture that burdens the room. Easy access to large niches (without removing the mattress) allows you to store everything you need for sleeping nearby, without bulky chests of drawers, while enjoying quality sleep on a full bed. However, it should be borne in mind that long-term and uninterrupted operation is only possible with proper assembly of the furniture. Any minor distortions or errors reduce the service life of the bed and quickly damage the lifting mechanisms. We suggest you familiarize yourself with the typical mistakes of self-assembly in order to prevent them from happening to your furniture.

Neglect of instructions. Even if you have experience, the instructions for the product should not be skipped. It may contain valuable explanations about the length and diameter of fasteners, technological holes, wood features, etc. Omission of nuances may not affect the final result, but may harm the product.
Assembly sequence is not correct. Jumping from one detail to another, looking ahead, is fraught with errors during the installation process. The desire to quickly assemble the bed is natural, but it is better not to get excited, but to carry out the steps step by step, according to the instructions.
Incorrect installation of the lift. The lifting mechanism for the bed consists of two parts: right and left. It is important not to confuse them, to install them strictly symmetrically, since the smallest errors will subsequently cause deformation of the box and breakdown of the mechanism.
Mistakes with mounting sockets. How to choose the optimal force when tightening bolts? This question, perhaps, was asked by every novice furniture maker, because you don’t want to have gaps in the assembled product, but you also don’t want to damage the mounting sockets on the new bed. We recommend tightening the connecting fittings moderately, and after completing assembly, tighten those places where there are gaps.
Unsuitable location for assembly. New flooring or a fluffy carpet are not the best surfaces for mounting bedroom furniture. In addition to the risk of damaging them, you will have additional complications during the assembly process. Therefore, it is important to prepare the place in advance, clear it of unnecessary objects, and, if necessary, cover it with construction film.
We hope that the instructions and recommendations described were useful to you and clarified some unclear points. Well, if a new bed is just in your plans, take a look at Dommino.ua, elegant samples for a comfortable sleep are always available.